High strength bolts of steel structures can be divided into friction type connections and pressure type connections from the mechanical characteristics. The connection surface of high-strength bolt pressure bearing connection only needs rust prevention treatment. However, the friction type of high-strength bolts has the advantages of tight connection, good stress, fatigue resistance and suitable for bearing dynamic loads. However, the connection surface needs to be treated with friction surface, which is generally treated by sandblasting and applying inorganic zinc rich paint after sandblasting.

鋼結構高強度螺栓由于螺栓構造和施工方法不一樣，又可以分為大六角頭高強度螺栓和扭剪型高強度螺栓兩類。大六角頭型和普通六角頭粗制螺栓相同，扭剪型的螺栓頭與鉚釘頭相仿，但是扭剪型的螺紋端頭設置了一個梅花卡頭和一個能夠控制緊固扭矩的環形槽溝，這個差別需要注意。

Due to different bolt structures and construction methods, steel structure high-strength bolts can be divided into two types: large hexagon head high-strength bolts and torsion shear high-strength bolts. The large hexagon head type is the same as the ordinary hexagon head rough bolt. The bolt head of the torsion shear type is similar to the rivet head, but the thread end of the torsion shear type is provided with a plum blossom chuck and an annular groove that can control the tightening torque. This difference needs attention.

—個螺栓連接副包括螺栓、螺母、墊圈三部分。高強度螺栓的構造要求和排列要求，與普通螺栓的構造及排列要求相同。然后一定要符合規范使用，大六角頭只能使用8.8級高強螺栓，扭剪型高強度螺栓只能使用10.9級高強度螺栓。

A bolt connection pair includes bolts, nuts and washers. The structural requirements and arrangement requirements of high-strength bolts are the same as those of ordinary bolts. Then it must be used in accordance with the specifications. Only grade 8.8 high-strength bolts can be used for large hexagon head, and only grade 10.9 high-strength bolts can be used for torsional shear high-strength bolts.

鋼結構高強度螺栓的預拉力是通過扭緊螺母實現的。通常使用扭矩法、轉角法或扭掉螺栓尾部梅花卡頭法來控制預拉力。

The pretension of steel structure high-strength bolts is realized by tightening nuts. Generally, torque method, angle method or quincunx clamp method at the end of the bolt are used to control the pretension.

目前有一種顯示扭矩的特制扳手，通過測定的扭矩和螺栓拉力之間的關系，再來施加扭矩達到必要的超張拉值。

At present, there is a special wrench that displays torque. By measuring the relationship between torque and bolt tension, torque is applied to achieve the necessary overstretch value.

轉角法轉角法又分為二個步驟，一是初擰，二是終擰。簡單來說，初擰一般是工人使用普通扳手使得被連接構件相互緊密貼合，而終擰則是以初擰的貼緊位置作為起點，根據螺栓直徑和板疊厚度來確定的終擰角度，用強有力的扳手旋轉螺母，擰預定角度值時，螺栓的拉力就可以達到要求的預拉力數值了。為了防止高強度螺栓受外部環境的影響，使扭矩系數發生變化，故一般初擰、終擰應該在同內完成。

Turning angle method turning angle method is divided into two steps, one is initial screwing and the other is final screwing. To put it simply, the initial tightening is generally that workers use ordinary wrenches to make the connected members closely fit each other, while the final tightening is that the final tightening angle is determined according to the bolt diameter and plate stack thickness with the initial tightening position as the starting point. When the nut is rotated with a powerful wrench to a predetermined angle, the bolt tension can reach the required pretension value. In order to prevent the torque coefficient of high-strength bolts from changing due to the influence of external environment, the initial tightening and final tightening should be completed in the same day.

扭剪型扭剪型高強度螺栓的受力特征與一般高強度螺栓相同，只是施加預拉力的方法為用擰斷螺栓梅花頭切口處截面來控制預拉力數值。

The mechanical characteristics of torsional shear high-strength bolts are the same as those of general high-strength bolts, except that the method of applying pretension is to control the pretension value by breaking the section at the notch of the bolt's quincunx head.

摩擦型高強度螺栓連接完全依靠被連接構件間的摩擦阻力傳力，而摩擦阻力的大小除了螺栓的預拉力外，與被連接構件材料及其接觸面的表面處理所確定的摩擦面抗滑移系數。

Friction type high-strength bolt connection completely relies on the frictional resistance between the connected members to transmit force. In addition to the pretension of the bolts, the magnitude of the frictional resistance is related to the anti slip coefficient of the friction surface determined by the surface treatment of the materials of the connected members and their contact surfaces.

以上就是為大家介紹的有關扭剪扳手的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://csbdjy.com

The above is a detailed introduction of the torsion shear wrench. I hope it can help you. If you have any questions, please contact us. We will provide you with services in a professional manner http://csbdjy.com