What are the maintenance methods of the torsion wrench? In fact, many users will encounter a series of problems when using the wrench, because these problems will seriously affect the efficiency of the work. Then we should fix it as soon as possible. Today, the twist-shear wrench knitted for the majority of users summed up a "quick maintenance method of twist-shear wrench" material.

　　扳手修理方法1:

　　Wrench repair method 1:

　　1. ，檢查你的扳手的傳感器連接線是否能夠連接好，與傳感器的信號線是短路還是開路，焊點是否存在虛焊現象。

　　1. First, check whether the sensor connection of your wrench can be well connected, whether the signal line of the sensor is short-circuited or open-circuited, and whether there is virtual welding in the solder joint.

　　B.扳手維修方法2:

　　B. Spanner Maintenance Method 2:

　　1、然后檢查你的電表是否能充飽電，如果充不飽也容易引起，不能正常開機使用，數值不穩定，就會跳線。當使用邏輯筆和示波器檢測信號時，請注意不要讓探頭同時接觸兩個2和測量銷，因?yàn)檫@種情況的本質是在通電的情況下形成短路。

　　1. Then check whether your meter is full or not. If it is not full, it is easy to cause it. If it can not be used properly, the value is unstable, and it will jump. When using logic pen and oscilloscope to detect signals, please be careful not to let the probe touch both 2 and measuring pins at the same time, because the essence of this situation is to form a short circuit in the case of electrification.

　　C.扳手修理方法3:

　　C. Spanner repair method 3:

　　用萬用表歐姆塊時，切記不要帶電測量。當檢測電源的濾波電容器的扭曲的剪切鉗、電解電源2,正極和負極的兩極容器應該短路,短路時,不要使用手表和筆線更換線停止放電電容器,因?yàn)樗苋菀谉艉诵木€(xiàn)。可以拿一個220V、50W的燈泡帶一個燈頭引線，連接到電容器的兩端，在放電時燈泡會閃光。

　　When using the ohmmeter block of the multimeter, remember not to measure on-line. When the twisted shear clamp, electrolytic power supply 2, positive and negative pole capacitors of the filter capacitor of the power supply should be short-circuited first, when short-circuited, do not use watch and pencil line to replace the line to stop discharge capacitor, because it is easy to burn off the core line. You can take a 220V, 50W bulb with a header lead and connect it to both ends of the capacitor. When discharging, the bulb will flash.
                 

　　D.扳手維修方法4:

　　D. Spanner Maintenance Method 4:

　　1、在測量每一點的參數時可以用普通的手工縫紉針焊接在萬用表筆上，這樣可以直接穿透漆層測量每一點，不需要大面積剝落漆層，這樣會形成銅箔的氧化。

　　1. When measuring the parameters of each point, the common manual sewing needle can be welded on the multimeter pen, which can directly penetrate the paint layer to measure each point without large area peeling off the paint layer, thus forming the oxidation of copper foil.

　　E.扳手修理方法5:

　　E. Spanner repair method 5:

　　1. 在潮濕的環境下，有必要測試一下萬用表是否能將電路板上的所有點都打開。

　　1. In a humid environment, it is necessary to test whether the multimeter can open all points on the circuit board.

　　2.因?yàn)檫@種情況下的主要故障是銅箔腐蝕。對于腐蝕的電路板，我們可以用95%的工業酒精清洗和擦拭，以免腐蝕較大的掩模。

　　2. Because the main failure in this case is the corrosion of copper foil. For corroded circuit boards, we can clean and wipe them with 95% industrial alcohol to avoid corroding larger masks.

　　3、在扭剪扳手的內部電路檢查時，在安裝部件的接點和電路基板上涂抹了絕緣清漆的情況下。

　　3. When checking the internal circuit of the Torsion-shear wrench, insulating varnish is applied to the connection of the installation component and the circuit board.

　　扭剪扳手的維修方法有哪些？以上是我們總結的扭剪扳手的維修方法，希望對您有幫助。

　　What are the maintenance methods of the torsion wrench? The above is our summary of the repair methods of the torsion shear wrench, I hope it will be helpful to you.